Okuma OSP Alarm & Error Code Reference

Shuts off power to the axis servo drives. The machine remains inoperative until the control is reset and the alarm cleared.

• 1071 — Memory board battery depleted. Replace quickly!
• 1089 — PLC alarm No. illegal
• 1091 — PLC alarm message file not found
• 1092 — PLC backup data file write
• 1093 — PLC backup data file not found
• 1094 — PLC back up data file read
• 1097 — Safety speed monitor error
• 1098 — MCS not responsive
• 1100 — Parameters not set
• 1101 — Blue screen
• 1102 — P100-Menu error
• 1103 — AlarmService internal error
• 1104 — DeviceNet slave idle mode
• 1105 — DTL error
• 1106 — FL-net initialization error
• 1107 — Major FL-net error
• 1108 — Non-responsive software detected
• 1109 — Error occurred during CAS
• 1110 — PLC control error
• 1111 — Shutting down to avoid damage
• 1112 — Non-functioning device detected
• 1113 — MCS Parameter learning error
• 1114 — MCS Inertia identification error
• 1120 — Overload detected.
• 1121 — PSC Optical scale encoder error
• 1122 — Safety controller error
• 1123 — Safety speed monitor error
• 1132 — VDU communication error
• 1133 — VDU detected error
• 1134 — VDU initialization failure
• 1135 — MCS DD encoder link error
• 1136 — MCS DD encoder error
• 1137 — MCS DD Encoder (slave sensor) error
• 1138 — MCS DD encoder initialization failure
• 1139 — MCS DD encoder (slave sensor) initialization failure
• 1144 — MCS Power supply unit overload
• 1146 — Tailstock torque over
• 1150 — MCS Undefined alarm number
• 1151 — MCS Inverter unit fault
• 1152 — Mistake in data from MCS to NC
• 1153 — MCS CON APA deviation
• 1154 — MCS Power supply unit error
• 1155 — MCS Converter link error
• 1156 — MCS DC-bus voltage alarm
• 1157 — MCS Motor overcurrent
• 1158 — MCS Power unit overheat
• 1159 — MCS Power unit overload
• 1160 — MCS Supply voltage flutter
• 1161 — MCS Inverter capacity differs from spec.
• 1162 — MCS Winding change failure
• 1163 — MCS Encoder link error
• 1164 — MCS Encoder detected error
• 1165 — MCS Encoder initialization failure
• 1166 — MCS Encoder with shaft detected error
• 1167 — MCS Encoder with shaft initialization failure
• 1168 — MCS ABSO SCALE error
• 1169 — MCS ABSO SCALE initialization failure
• 1170 — MCS Magnetic encoder alarm
• 1171 — MCS Resolver alarm
• 1172 — MCS Pulse generator count over
• 1173 — MCS Motor overheat
• 1174 — MCS Servo link error
• 1175 — MCS Servo link disconnection
• 1176 — Mistake in data from NC to MCS
• 1177 — MCS Servo data error
• 1178 — MCS Illegal command
• 1179 — MCS CON speed over
• 1180 — MCS Speed command over
• 1181 — MCS DIFF over
• 1182 — MCS APA speed over
• 1183 — MCS Full-closed APA error
• 1184 — MCS Over speed
• 1185 — MCS Speed deviation over
• 1186 — MCS Collision detected
• 1187 — MCS Urgent-stop time over
• 1188 — MCS Belt is broken
• 1189 — MCS Axis change control error
• 1190 — MCS Independent encoder initialization failure
• 1191 — MCS Calculated current position lies outside range
• 1192 — MCS Motor overload
• 1194 — MCS ABSO SCALE sub-slider error
• 1195 — MCS Tandem control communication error
• 1196 — MCS Full abso scale link error
• 1197 — MCS Full abso scale error
• 1198 — MCS Full abso scale initialization failure
• 1199 — MCS Axis stop signal error
• 1200 — Stroke end over
• 1202 — Plus variable limit over
• 1203 — Minus variable limit over
• 1213 — User reserve code
• 1215 — S.M command asynchronous
• 1216 — Synchronous P code error
• 1217 — Torque limiter
• 1218 — Torque limiter cancel
• 1219 — Torque limit over
• 1220 — Torque skip condition not satisfied
• 1221 — Duplicate M-code
• 1222 — Interrupt return pointer mismatch
• 1223 — Thread feed command error
• 1225 — Contour generation calculation error
• 1228 — Illegal spindle mode
• 1229 — Max. spindle rotation count not specified
• 1238 — Spindle moved to interference distance
• 1243 — Turret rotation conditions
• 1245 — Axis moved to tool interference area
• 1257 — Axis moved to chuck barrier area
• 1258 — Axis moved to tailstock barrier area
• 1259 — Tow-along tailstock connecting
• 1260 — Tow-along tailstock command not possible
• 1262 — W-axis plus variable limit over
• 1263 — W-axis minus variable limit over
• 1265 — Parts catcher interlock
• 1272 — Load exceeds No.2 limit value
• 1273 — Load monitor command already executed
• 1278 — Laser measurement data NG
• 1279 — IND. CMP. data verification failure
• 1280 — HP9825A unable to receive
• 1281 — Abnormal data from HP9825A
• 1282 — Data error from HP9825A
• 1283 — C-axis command not possible
• 1299 — Axis moved to sub-spindle interference distance
• 1300 — W-axis unable to move
• 1303 — Pickoff index position
• 1306 — Sensor touch G00
• 1307 — No contact with sensor
• 1309 — Sensor protect
• 1316 — ATC manual operation mode impossible
• 1322 — Y-axis parameter illegal
• 1323 — Illegal YS-axis position
• 1328 — Adaptive control communication error
• 1329 — Shift amount error
• 1332 — Spindle belt slip
• 1334 — APA error
• 1336 — Moved inside horizontal barrier area
• 1338 — LOAD MONITOR W overload
• 1339 — Spindle different from position when door open
• 1345 — Unable to move to tool change position
• 1347 — STM time over
• 1348 — Cycle time over
• 1349 — Contour generation impossible
• 1353 — Measurement system error
• 1355 — Tow-along steady rest connected
• 1356 — Steady rest torque over
• 1357 — Positioning uncertain
• 1367 — NC tailstock position error
• 1376 — Cutting error
• 1393 — Tow-along steady rest interference position
• 1412 — HOME POSITION movement interlock
• 1426 — Moved inside barrier area
• 1431 — Safety speed over
• 1432 — Safety monitor error detection
• 1435 — Turret interference
• 1436 — Power ON APA deviation
• 1440 — Steady rest-Tailstock interlock
• 1441 — Safety speed clamp
• 1453 — Heavy work data not found
• 1460 — TEMP RISE LIMIT OVER
• 1463 — Spindle moved inside transportation barrier
• 1465 — Spindle low acceleration mode condition
• 1466 — HOB cutting overload
• 1467 — Position scale error XS-axis
• 1468 — Servo amp error XS-axis
• 1469 — APA speed XS-axis
• 1470 — APA range XS-axis
• 1471 — CON speed XS-axis
• 1472 — Stroke end over XS-axis
• 1473 — Actual position initialization error XS-axis
• 1474 — Learning control error XS AXIS
• 1475 — CAM execution data not selected XS-axis
• 1476 — Learning control command XS-axis
• 1477 — Syncronous mode command
• 1478 — Chuck coordinates mismatch
• 1479 — PSCB command error
• 1480 — DIFF over XS-axis
• 1481 — Drift compensation value over
• 1482 — PSCB Real-time task error
• 1483 — PSCB INT task loop error
• 1484 — PSCB EC task loop error
• 1485 — PSCB Time sharing task error
• 1486 — PSCB Exception error
• 1487 — PSCB Memory test error
• 1488 — PSCB Overheat
• 1489 — First time drift compensation value over
• 1490 — Synchronous mode spindle speed command
• 1491 — Heavy tooling data not found
• 1492 — PSCB P.G. underpulse
• 1493 — PSCB P.G. overpulse
• 1494 — PSCB Minus stroke end over
• 1500 — Workpiece rest interlock
• 1501 — Workpiece rest torque over
• 1504 — Alarm-A at other system
• 1507 — Unable to enter C-axis sync. Mode
• 1509 — A turret and B turret interference
• 1510 — Unable to execute Hi-CUT Pro control
• 1511 — SPM contour control not possible
• 1512 — SPM contour control error
• 1513 — Unable to clamp workpiece
• 1514 — Clutch A slip over limit
• 1515 — Mistake in X, Z commands
• 1516 — NC tailstock slide resistance over
• 1517 — Turret or tool not at index cut position
• 1519 — Spindle phase over limit
• 1520 — Synchronous error limit over
• 1521 — NC tailstock error
• 1522 — Linear guide cover interference area
• 1523 — Workpiece weight data file not found
• 1524 — Feed speed over
• 1525 — M-tool spindle speed over in Hob mode
• 1526 — Turret index error position
• 1527 — Unable to execute while mounting LBB
• 1528 — The attachment status mismatch
• 1529 — M axis belt slip
• 1530 — Steady-rests interference position
• 1531 — Tool posture fluctuation reduction error
• 1532 — Turret interference distance intrusion
• 1682 — Magnetic encoder speed detection error
• 1683 — MCS Rotary encoder 5 initialization failure
• 1684 — MCS Rotary encoder 5 error
• 1685 — MCS Rotary encoder 4 initialization failure
• 1686 — MCS Rotary encoder 4 error
• 1687 — MCS Rotary encoder 3 initialization failure
• 1688 — MCS Rotary encoder 3 error
• 1689 — MCS Rotary encoder 2 error
• 1690 — MCS Rotary encoder 1 initialization failure
• 1691 — MCS Rotary encoder 1 error
• 1692 — MCS Linear scale 4 initialization failure
• 1693 — MCS Linear scale 4 error
• 1694 — MCS Linear scale 3 initialization failure
• 1695 — MCS Linear scale 3 error
• 1696 — MCS Linear scale 2 initialization failure
• 1697 — MCS Linear scale 2 error
• 1698 — MCS Linear scale 1 initialization failure
• 1699 — MCS Linear scale 1 error
• 1700 — Emergency stop
• 1701 — EC overload
• 1702 — BDU overload
• 1703 — EC circuit breaker
• 1704 — Transformer overheat
• 1705 — Oil pressure low
• 1706 — Alarm detected from externally connected device
• 1707 — Stroke end over
• 1708 — Canceling stroke end limit
• 1709 — XA-axis overload
• 1710 — XB-axis overload
• 1711 — ZA-axis overload
• 1712 — ZB-axis overload
• 1713 — Spindle rotation interlock
• 1714 — S.M command asynchronous
• 1715 — Spindle revolution over
• 1716 — M03/M04 change command failure
• 1717 — Unable to use M40, M43, M44 commands
• 1718 — Tow-along tailstock command error
• 1719 — Gear command/position mismatch
• 1720 — Gear command error
• 1721 — Gear neutral
• 1722 — M19 command issued when gear neutral
• 1723 — Z-axis moved to spindle interference distance
• 1724 — Spindle synchronization interlock
• 1725 — Impossible command issued during spindle synchronization
• 1726 — C-axis command not possible
• 1727 — C-axis ON/OFF command not possible
• 1728 — C-axis clamp/unclamp command not possible
• 1729 — Unable to confirm C-axis advance
• 1730 — Turret clamp/position check error
• 1731 — Turret index control alarm
• 1732 — Turret rotation interlock
• 1733 — Tool number input error
• 1734 — Pickoff chuck interlock
• 1735 — Sub-spindle chuck pressure insufficient
• 1736 — Pickoff index interlock
• 1737 — Turret unclamp interlock
• 1738 — Turret rotation impossible
• 1739 — Chuck clamp pressure insufficient
• 1740 — Chuck open/close interlock
• 1741 — Chuck unclamp
• 1742 — Chuck interlock cancel interlock
• 1743 — Index chuck interlock
• 1744 — Air chuck pressure error
• 1745 — Chucking miss
• 1746 — Chuck missclamp
• 1747 — No tailstock quill advance answer
• 1748 — Tailstock quill advance over
• 1749 — Tailstock quill command error
• 1750 — Tailstock interference
• 1751 — Tow-along tailstock ON/OFF interlock
• 1752 — Tow-along tailstock clamp/unclamp error
• 1753 — Parts catcher interlock
• 1754 — Coupling device alarm
• 1755 — Robot inside machine
• 1756 — Loader inside machine
• 1757 — Loader interlock
• 1758 — Loader not at escape position
• 1759 — Loader/robot not at escape position
• 1760 — Revolution tool M13/M14 change not possible
• 1761 — Revolution tool gear mismatch
• 1762 — Revolution tool gear interlock
• 1763 — Tool revolution interlock
• 1764 — Tool rotating when T command issued
• 1765 — Rotation tool index interlock
• 1766 — Rotation tool over speed
• 1767 — M-axis clutch connection error
• 1768 — Sub-spindle rotation over
• 1769 — Sub-spindle index interlock
• 1770 — Door interlock
• 1771 — Door open/close limit switch NG
• 1772 — Door open/close condition
• 1773 — Unable to restore axis position when door closed
• 1774 — Sensor head advance/retract interlock
• 1775 — Touch setter limit
• 1776 — Sensor head not at retract position
• 1777 — ATC change arm position error
• 1778 — No dummy tool in ATC turret
• 1779 — Manual tool change operation interlock
• 1780 — ATC system mode interlock
• 1781 — Loader/robot interference
• 1782 — Power sequence error
• 1783 — Turret unclamp time over
• 1784 — Turret clamp time over
• 1785 — NC parameter data transfer error
• 1786 — Coolant error
• 1787 — Door open/close check NG
• 1788 — Safety door open
• 1789 — Steady rest interlock
• 1790 — Bar feeder not ready
• 1791 — Bar feeder advance/retract interlock
• 1792 — Turret rotation interlock
• 1793 — Side cover interlock
• 1794 — Rear cover interlock
• 1795 — Side cover open/close lmt switch NG
• 1796 — Turret index clutch disconnect error
• 1797 — Invalid mode switch
• 1798 — Steady rest missclamp
• 1799 — Sensor protection cover interlock
• 1800 — Locking switch NG
• 1801 — Bar feeder setting position mismatch
• 1802 — Safety guard interlock
• 1803 — Machine enabling button error
• 1804 — Safety speed monitor output error
• 1805 — Teaching panel enabling switch error
• 1806 — ATC Logic data file error
• 1807 — Shutter close not possible
• 1808 — Safety fence locking switch NG
• 1809 — Manual command time over
• 1810 — Safety guard interlock
• 1811 — Loader axis unable to move
• 1812 — Mist lubrication unit error
• 1813 — 2nd spindle condition satisfy
• 1814 — W-axis movement interlock
• 1815 — Face driver pressure insufficient
• 1816 — Safety fence open
• 1817 — Setup switch ON
• 1818 — Hand slide interlock
• 1819 — Hand turning interlock
• 1820 — Turnover interlock
• 1821 — Magazine door lock error
• 1822 — Slide step interlock
• 1823 — Vibration cutter faulty
• 1824 — Oil cooler error
• 1825 — Spindle cooling unit error
• 1826 — Oil air lubrication illegal
• 1827 — Setup switch ON
• 1828 — Laser sensor interlock
• 1829 — Sp. oil air lub. air pressure error
• 1830 — SP. oil air lub. oil level error
• 1831 — Sp. oil air lub. oil pressure error
• 1832 — Unloader advance/retract interlock
• 1833 — Tow-along steady rest unclamp interlock
• 1834 — Door interlock
• 1835 — Workpiece receiver interlock
• 1836 — Interference area intrusion
• 1837 — Worktable overload
• 1838 — Workpiece stabilizer interlock
• 1839 — Deburring tool interlock
• 1840 — M code data file mismatch
• 1841 — Swing interlock
• 1842 — Wrist rotation interlock
• 1843 — Workpiece rest interlock
• 1844 — Workpiece pusher interlock
• 1845 — Hand rotation interlock
• 1846 — Chuck grip confirmation unit faulty
• 1847 — Tailstock air miss detection input NG
• 1848 — Chuck grip failure
• 1849 — Workpiece unloading unit interlock
• 1850 — Robot/Loader emergency stop
• 1851 — Air pressure insufficient
• 1852 — NC alarm
• 1853 — Oil pressure insufficient
• 1854 — Error detected from externally connected device
• 1855 — M code time over
• 1856 — Circuit breaker tripped
• 1857 — Intrusion interlock
• 1858 — No hand open/close output
• 1859 — Swing position no output
• 1860 — Axis interlock
• 1861 — Stroke end over
• 1862 — Canceling stroke end limit
• 1863 — Loader interference
• 1864 — Z/C-axis not in rotation possible area
• 1865 — Swing position indefinite
• 1866 — No workpiece clamped on hand A
• 1867 — No workpiece clamped on hand B
• 1868 — Wrist broken
• 1869 — Hand open/ close interlock
• 1870 — Hand clamp confirmation
• 1871 — Coupling device error
• 1872 — Safety fence interlock
• 1873 — Door interlock
• 1874 — Interlock release NG
• 1875 — Safety fence lock NG
• 1876 — Swing interlock
• 1877 — Robot/Loader power sequence error
• 1878 — Machine start impossible
• 1879 — Workpiece puller holder interlock
• 1880 — Loader hand/machine interference
• 1881 — Part turnover device R clamp empty
• 1882 — Part turnover device L clamp empty
• 1883 — Part turnover device R advanced too far
• 1884 — Part turnover device L advanced too far
• 1885 — Loader/part turnover device interference
• 1886 — Wrist turning position indefinite
• 1887 — Workpiece puller interlock
• 1888 — Backup roller interlock
• 1889 — Auto workpiece I/O unit FWD pressure low
• 1890 — Coolant flow insufficient
• 1891 — Unloader interference position
• 1892 — Unloader interlock
• 1893 — Running mode error
• 1894 — Running mode error
• 1895 — Fire alarm
• 1896 — Air source pressure low
• 1897 — Lower turret drive belt torn
• 1898 — OP panel within interference range
• 1899 — Safety fence open
• 1900 — Plus variable limit over
• 1901 — Minus variable limit over
• 1920 — User reserve code
• 1922 — Torque limit over
• 1924 — Barrier intrusion
• 1927 — M code time over
• 1928 — Cycle time over
• 1938 — Machine start impossible
• 1939 — Hand open/close interlock
• 1940 — Loader Z-axis stopper set
• 1941 — Safety guard interlock
• 1942 — Safety speed over
• 1943 — Safety speed monitor error
• 1944 — Safety monitor error detection
• 1945 — Running mode error
• 1949 — Alarm-A at other system
• 1950 — Safety speed monitor error
• 1951 — Safety controller error
• 8500 — Cut off error
• 8501 — ATC shutter not close
• 8502 — Unable to G21
• 8503 — Spindle internal centering unit interlock
• 8504 — Tool change command
• 8505 — Tow-along steady rest clamp/unclamp
• 8506 — Combination chuck interlock
• 8507 — Automatic lubrication system error
• 8508 — Coolant filter
• 8509 — Cutting feed interlock
• 8510 — Oil unit error
• 8511 — B-axis clamp/unclamp interlock
• 8512 — Turret position uncertain
• 8513 — Coolant interlock
• 8514 — Work conveyor interlock
• 8515 — Work ejector interlock
• 8516 — Touch setter unlock time over
• 8517 — Work hand interlock
• 8518 — Bar Feeder illegal
• 8520 — Stopper interlock
• 8521 — Work measurement operation
• 8522 — Locater oil pressure
• 8523 — Locater condition
• 8524 — Oil motor overload
• 8525 — Coolant motor overload
• 8526 — Spindle cooling motor overload
• 8527 — Oil skimmer overload
• 8528 — Magnet separator overload
• 8529 — Tool monitoring unit error detection
• 8530 — Laser sensor input data error
• 8531 — Door open
• 8532 — Polish Material unit interlock
• 8536 — Operation ready OFF condition
• 8537 — Magazine door Interlock
• 8538 — ATC shutter barrier area
• 8539 — Complete stop
• 8540 — X-axis in interference range
• 8541 — Spindle phase synchronization interlock
• 8542 — Synchronizing spindle phase
• 8543 — Measurement Unit error
• 8545 — Illegal robot/loader request
• 8546 — Rolling-head movement error
• 8547 — Drive jig unit interlock
• 8548 — ACC interlock
• 8549 — ACC door interlock
• 8550 — ACC manual operation mode impossible
• 8551 — Semi-dry unit error
• 8552 — Sub-chuck interlock
• 8553 — ACC airblow interlock
• 8554 — Spindle table rotation
• 8555 — B-Axis movement
• 8556 — No mount magazine
• 8557 — Tool Breakage sensor error
• 8558 — L-tool index command
• 8559 — Part turn device advanced too far
• 8560 — Override switch failure
• 8561 — Grinding whl spindle motor overload
• 8562 — Whl spdl coolant pressure drop/loss
• 8563 — Inverter failure
• 8564 — Turret drive belt disconnection
• 8566 — Tool clamp interlock
• 8567 — Spindle cover open/close limit SW NG
• 8568 — Insulation error
• 8569 — Magazine turn interlock
• 8570 — Magazine tool No.
• 8571 — Irregular coolant level
• 8572 — ATC step time over
• 8573 — Spingdle vibration
• 8574 — MCS operation ready off
• 8575 — Grinding whl spindle unit
• 8576 — Grinding whl spindle unit interlock
• 8577 — Axis interlock
• 8578 — Coupling device interlock
• 8579 — Tailstock and turret interference
• 8580 — Canceling interference detection
• 8581 — Loader automatic operation
• 8582 — Illegal workpiece pusher confirmation
• 8583 — ATC change arm overload
• 8584 — Tailstock high/low change interlock
• 8585 — Coiling prevention equip. interlock
• 8586 — Air picker broken
• 8587 — AREA SENSOR interlock
• 8588 — Coolant Flow
• 8589 — Chip conveyor faulty
• 8590 — Tailstock pedestal condition
• 8591 — C-axis synchronous condition
• 8592 — Synchronizing C-axis
• 8593 — Chip crusher error
• 8594 — Sensor overstroke
• 8595 — Linear guide cover interference
• 8596 — Safety plug interlock
• 8597 — Shuttle device hand clamp empty
• 8598 — Ceiling door interlock
• 8599 — Illegal tool clamp unit
• 8600 — Ceiling door open/close limit SW NG
• 8601 — ATC tool change arm inverter failure
• 8602 — Chip pan cover interlock
• 8603 — C-axis clamp/unclamp condition
• 8604 — Long tool change protection
• 8605 — Drive belt disconnection
• 8606 — APC door open/close limit NG
• 8607 — XB cover interference
• 8608 — Illegal touch setter unit
• 8609 — Axis overheat
• 8610 — Invalid spindle winding condition
• 8611 — Winding change error
• 8612 — APC interlock
• 8613 — APC clamp/unclamp time over
• 8614 — APC escape position
• 8615 — ATC shutter not open
• 8616 — Coolant level low
• 8617 — Thru-the-tool coolant filter clogged
• 8618 — M spindle overload
• 8619 — Machine axis travel limit over
• 8620 — PLC system data
• 8621 — M spindle air curtain pressure low
• 8622 — Hydraulic unit oil level low
• 8623 — Mist air lubrication unit
• 8624 — Axis interlock
• 8625 — Tool revolution command
• 8626 — Ceiling door guide interlock
• 8627 — Long boring bar change protection
• 8628 — Spindlehead lib oil level low
• 8629 — Spindlehead lubricant pressure low
• 8630 — Hydraulic pressure drop
• 8631 — Invalid safety-monitor spec.
• 8632 — UNUSABLE interrupt program
• 8633 — AAC Operation mode impossible
• 8634 — ATC shutter open/close condition
• 8635 — Spindle actual position detection error
• 8636 — RSS unit Battery error
• 8637 — RSS unit Communication error
• 8638 — Sub-spindle head clamp condition
• 8639 — Tailstock control mode ON/OFF cond.
• 8640 — Center partition interlock
• 8643 — Unusable PLC spec. code
• 8644 — Fire extinguish unit power OFF
• 8645 — Fire extinguish unit error
• 8646 — Fire ext. unit power OFF or error
• 8647 — Hand open/close switch NG
• 8648 — Tailstock tool mode mismatch
• 8649 — Measurement sensor unit interlock
• 8680 — Area sensor interlock

Program and command-level errors — usually a syntax, variable, or command mistake in the running NC program.

• 2049 — PLC axis stroke end over
• 2050 — PLC axis command
• 2051 — PLC axis continuous positioning over
• 2052 — Blue screen
• 2053 — P100-Menu error
• 2058 — Error occurred while CAS work
• 2059 — Non-functioning device detected
• 2060 — Fan motor error on panel computer unit
• 2090 — The remaining time after relocation has passed
• 2092 — MCS Parameter learning error
• 2114 — MCS Inertia identification error
• 2120 — Overload detected.
• 2132 — VDU communication error
• 2133 — VDU detected error
• 2134 — VDU initialization failure
• 2135 — MCS DD encoder link error
• 2136 — MCS DD Encoder error
• 2137 — MCS DD Encoder (slave sensor) error
• 2138 — MCS DD encoder initialization failure
• 2139 — MCS DD encoder (slave sensor) initialization failure
• 2144 — MCS Power supply unit overload
• 2150 — MCS Undefined alarm number
• 2151 — MCS Inverter unit fault
• 2152 — Mistake in data from MCS to NC
• 2153 — MCS CON APA deviation
• 2154 — MCS Power supply unit error
• 2155 — MCS Converter link error
• 2156 — MCS DC-bus voltage alarm
• 2157 — MCS Motor overcurrent
• 2158 — MCS Power unit overheat
• 2159 — MCS Power unit overload
• 2160 — MCS Supply voltage flutter
• 2161 — MCS Inverter capacity differs from spec.
• 2162 — MCS Winding change failure
• 2163 — MCS Encoder link error
• 2164 — MCS Encoder detected error
• 2165 — MCS Encoder initialization failure
• 2166 — MCS Encoder with shaft detected error
• 2167 — MCS Encoder with shaft initialization failure
• 2168 — MCS ABSO SCALE error
• 2169 — MCS ABSO SCALE initialization failure
• 2170 — MCS Magnetic encoder alarm
• 2171 — MCS Resolver alarm
• 2172 — MCS Pulse generator count over
• 2173 — MCS Motor overheat
• 2174 — MCS Servo link error
• 2175 — MCS Servo link disconnection
• 2176 — Mistake in data from NC to MCS
• 2177 — MCS Servo data error
• 2178 — MCS Illegal command
• 2179 — MCS CON speed over
• 2180 — MCS Speed command over
• 2181 — MCS DIFF over
• 2182 — MCS APA speed over
• 2183 — MCS Full-closed APA error
• 2184 — MCS Over speed
• 2185 — MCS Speed deviation over
• 2186 — MCS Collision detected
• 2187 — MCS Urgent-stop time over
• 2188 — MCS Belt is broken
• 2189 — MCS Axis change control error
• 2190 — MCS Independent encoder initialization failure
• 2191 — MCS Calculated current position lies outside range
• 2192 — MCS Motor overload
• 2194 — MCS ABSO SCALE sub-slider error
• 2195 — MCS Tandem control communication error
• 2196 — MCS Full abso scale link error
• 2197 — MCS Full abso scale error
• 2198 — MCS Full abso scale initialization failure
• 2199 — MCS Axis stop signal error
• 2200 — G-code error
• 2201 — M-code error
• 2202 — Common variable error
• 2203 — System variable error
• 2204 — Sequence name error
• 2205 — Numeric data error
• 2206 — Character use error
• 2207 — Program name error
• 2208 — Character string error
• 2209 — Hexadecimal data error
• 2210 — Spindle max revolution error
• 2212 — G132/G133 command error
• 2213 — Program factor over
• 2214 — Subscript left side incorrect
• 2215 — Local variable use over
• 2216 — System variable setting data over
• 2217 — Output variable setting data mistake
• 2218 — UNUSABLE G-code
• 2219 — UNUSABLE M-code
• 2220 — Subscript left side illegal
• 2221 — UNUSABLE output variable No
• 2222 — UNUSABLE input variable No
• 2223 — UNUSABLE turret direct code
• 2224 — UNUSABLE contour generation command
• 2225 — UNUSABLE Y-Z circle command
• 2226 — UNUSABLE thread cutting command
• 2227 — Mnemonic or local variable mistake
• 2228 — VSET sequence left command mistake
• 2229 — EXPRESSION right side
• 2230 — EXPRESSION calculation error
• 2231 — EXPRESSION syntax incorrect
• 2232 — EXPRESSION subscript mistake
• 2233 — EXPRESSION buffer over
• 2234 — EXPRESSION local variable
• 2235 — Equal does not exist
• 2236 — Program end code not found
• 2237 — BRANCH (IF,GOTO) sequence name
• 2238 — BRANCH(IF,GOTO) condition
• 2239 — Mistake in F command
• 2240 — Mistake in F/E command
• 2241 — Mistake in I command
• 2242 — Mistake in J command
• 2243 — Mistake in K command
• 2244 — Mistake in L command
• 2245 — Mistake in P command
• 2246 — Mistake in S command
• 2247 — No S command
• 2248 — Mistake in T command
• 2249 — Mistake in X command
• 2250 — Mistake in X/Z command
• 2251 — Mistake in Z command
• 2252 — Mistake in arc command
• 2253 — Mistake in angle command
• 2254 — Mistake in thread cutting cycle command
• 2255 — Mistake in arc radius command
• 2256 — Mistake in D command
• 2257 — Mistake in gauging cycle command
• 2258 — Mistake in C command
• 2259 — Mistake in SB command
• 2260 — Mistake in QA command
• 2261 — Mistake in X/Y command
• 2262 — Mistake in incremental command
• 2263 — Command required for X-, Y-axes
• 2264 — Mistake in Y command
• 2265 — Distance calculation over limit
• 2266 — Mistake in R command
• 2267 — Mistake in drilling cycle command
• 2268 — Mistake in angle command
• 2269 — Angle chamfering command error
• 2270 — Mistake in CD command
• 2271 — Mistake in CL command
• 2272 — Mistake in TM command
• 2273 — Mistake in W command
• 2274 — Mistake in CB command
• 2275 — Mistake in HP command
• 2276 — Mistake in CC command
• 2277 — Mistake in torque limit command
• 2278 — SUB PROGRAM repetition
• 2279 — SUB PROGRAM stack
• 2280 — SUB PROGRAM program name
• 2281 — SUB PROGRAM data print
• 2282 — SCHEDULE PROGRAM Q
• 2283 — SCHEDULE PROGRAM mnemonic code
• 2284 — SCHEDULE PROGRAM program end
• 2285 — SCHEDULE PROGRAM main program load
• 2286 — Plus variable limit over
• 2287 — Minus variable limit over
• 2288 — User reserve code
• 2289 — Unable to write backup data file
• 2290 — Program name not selected
• 2291 — Main sequence error
• 2292 — Restart failure
• 2293 — MDI special G-code
• 2294 — Special G-code table
• 2295 — STM time over
• 2296 — UGC No program end code
• 2297 — UGC DELETE syntax
• 2298 — UGC DEF syntax
• 2299 — UGC TIP syntax
• 2300 — UGC TIF syntax
• 2301 — UGC No shape entry
• 2302 — UGC Illegal numerical data
• 2303 — UGC Illegal character
• 2304 — UGC User variable
• 2305 — UGC System variable
• 2306 — UGC Illegal command
• 2307 — UGC Program factor over
• 2308 — UGC Coordinate data
• 2309 — UGC END syntax
• 2310 — UGC Command over
• 2311 — UGC Command format
• 2312 — UGC Additional parameter
• 2313 — UGC Expression
• 2314 — UGC Figure entry area over
• 2315 — UGC Unable to delete
• 2316 — READ/WRITE No spec
• 2317 — READ/WRITE Buffer over
• 2318 — READ/WRITE Device No.
• 2319 — READ/WRITE Data
• 2320 — READ communication error
• 2321 — WRITE communication error
• 2322 — GET/PUT No spec.
• 2323 — GET/PUT Buffer over
• 2324 — GET/PUT Number of digits
• 2325 — GET/PUT Variable designation
• 2326 — GET Numerical data
• 2327 — Calculation function no spec.
• 2328 — Sub-program no spec.
• 2329 — Sub-spindle interference distance
• 2330 — Input/output variable no spec.
• 2331 — Multiple machining no spec.
• 2332 — Sub-spindle no spec.
• 2334 — In-process gauging no spec.
• 2335 — Post-process gauging no spec.
• 2336 — Animation no spec.
• 2337 — Graphic backup data file write failure
• 2338 — Spindle orientation no spec.
• 2339 — Load monitor no spec.
• 2340 — Thread phase matching no spec.
• 2341 — Circular thread cutting no spec.
• 2342 — Circular thread cutting command
• 2343 — Tool retract no spec.
• 2344 — Tool retract interrupt enable com.
• 2345 — Tool retract interrupt disable com.
• 2346 — Tool retract interrupt return com.
• 2347 — ROBOT no spec.
• 2348 — ROBOT program name
• 2349 — LOADER no spec.
• 2350 — LOADER program name
• 2351 — Coupling device program select no spec.
• 2353 — CHAMFERING G01 mode
• 2354 — CHAMFERING L over
• 2355 — CHAMFERING L illegal order
• 2356 — CHAMFERING X, Z illegal order
• 2357 — CHAMFERING Any angle calculation
• 2358 — CHAMFERING Any angle
• 2359 — NOSE-R COMP. No spec.
• 2360 — NOSE-R COMP. NOSE-R > circle-R
• 2361 — NOSE-R COMP. Calculation
• 2362 — NOSE-R COMP. Cancel G00 G01
• 2363 — NOSE-R COMP. No cross point
• 2364 — NOSE-R COMP. Entrance command error
• 2365 — NOSE-R COMP. Thread cutting cycle
• 2366 — TOOL RADIUS COMP. No spec.
• 2367 — TOOL RADIUS COMP. NOSE-R comp. surface change
• 2368 — TOOL RADIUS COMP. C-axis separation
• 2369 — TOOL RADIUS COMP. QA command
• 2370 — TOW-ALONG TAILSTOCK MOVEMENT no spec.
• 2371 — TOW-ALONG TAILSTOCK MOVEMENT condition
• 2372 — LASER MEASUREMENT no spec.
• 2373 — LASER MEASUREMENT condition
• 2374 — LAP No spec.
• 2375 — LAP B illegal order
• 2376 — LAP D illegal order
• 2377 — LAP DA(DB) illegal order
• 2378 — LAP H illegal order
• 2379 — LAP H-U(W) < D (M73)
• 2380 — LAP U(W) illegal order
• 2381 — LAP U(W) > H
• 2382 — LAP XA(ZA), XB(ZB) illegal order
• 2383 — LAP Calculation error
• 2384 — LAP Down step number over
• 2385 — LAP Entry in LAP
• 2386 — LAP Sequence name
• 2387 — Unable to LAP Control
• 2388 — LAP No G-code
• 2389 — LAP NOSE-R comp. cancel
• 2390 — LAP Entry in NOSE-R comp.
• 2391 — LAP Shape designation
• 2392 — MULTI CYCLE B illegal order
• 2393 — MULTI CYCLE D illegal order
• 2394 — MULTI CYCLE F illegal order
• 2395 — MULTI CYCLE H illegal order
• 2396 — MULTI CYCLE H-U(W) < D (M73)
• 2397 — MULTI CYCLE I,K over
• 2398 — MULTI CYCLE I,K illegal order
• 2399 — MULTI CYCLE L illegal order
• 2400 — MULTI CYCLE Entry in LAP
• 2401 — MULTI CYCLE U(W) illegal order
• 2402 — MULTI CYCLE U(W) > H
• 2403 — MULTI CYCLE X,Z illegal order
• 2404 — MULTI CYCLE Angle
• 2405 — MULTI CYCLE Tool offset
• 2406 — MULTI CYCLE Cycle start point
• 2407 — MULTI CYCLE Entry in NOSE-R comp.
• 2408 — MULTI CYCLE Width
• 2409 — TOOL LIFE CONTROL no spec.
• 2410 — Tool life management No spare tool
• 2411 — TOOL LIFE CONTROL tool group
• 2412 — TOOL LIFE CONTROL no T-entry
• 2413 — TOOL LIFE CONTROL tool offset group
• 2414 — TOOL LIFE CONTROL no T-offset
• 2415 — MULTI-MACHINING CYCLE No spec.
• 2416 — MULTI-MACHINING CYCLE C
• 2417 — MULTI-MACHINING CYCLE I,K
• 2418 — MULTI-MACHINING CYCLE Q
• 2419 — MULTI-MACHINING CYCLE F
• 2420 — MULTI-MACHINING CYCLE L
• 2421 — MULTI-MACHINING CYCLE D
• 2422 — MULTI-MACHINING CYCLE X,Z
• 2423 — MULTI-MACHINING CYCLE SA
• 2424 — MULTI-MACHINING CYCLE Feed G94
• 2425 — MULTI-MACHINING CYCLE A
• 2426 — MULTI-MACHINING CYCLE Thread cycle
• 2427 — MULTI-MACHINING CYCLE U,W
• 2428 — MULTI-MACHINING CYCLE SB
• 2429 — MULTI-MACHINING CYCLE Y-axis mode
• 2430 — ATC no spec.
• 2431 — ATC syntax
• 2432 — ATC TC
• 2434 — ATC TL
• 2435 — ATC MT
• 2436 — ATC MG
• 2438 — Unable to M06/M228 command
• 2440 — Y-axis no spec.
• 2441 — 2 saddle machine no spec.
• 2444 — Carrier axis variable limit over
• 2445 — 3-D coordinate conversion
• 2452 — Chuck barrier area
• 2453 — Tailstock barrier area
• 2456 — W-axis minus variable limit over
• 2457 — X-axis correction stroke end over
• 2459 — Restart axis position is illegal
• 2460 — Change timing G13/G14
• 2462 — Change timing G122/G123
• 2463 — Change timing G140/G141/G142
• 2464 — Spindle/turret G-code
• 2465 — G122/G123 command mismatch
• 2466 — Unable to issue M100 command during Nose-R comp.
• 2472 — Y-axis control mode
• 2475 — W-axis command G-code
• 2476 — Mirror image coordinate selection
• 2477 — Sub-spindle mode
• 2478 — No workpiece coordinate mode command
• 2479 — Contour generation calculation error
• 2480 — G132/G133 command error
• 2486 — NC turret no spec.
• 2487 — Unable to select coordinates
• 2488 — UNUSABLE X-axis command
• 2489 — NC tailstock parameter error
• 2490 — Chuck pressure out of range
• 2491 — Horizon barrier intrusion
• 2492 — Interrupt program: illegal command
• 2493 — Linked external equipment program selection
• 2494 — Chuck pressure command illegal
• 2495 — Inverse time feed command format
• 2496 — CAM data cannot be transmitted.
• 2497 — T code
• 2498 — Learning cannot be executed.
• 2499 — Spindle marker latch data error
• 2500 — MULTI-MACHINING CYCLE HS,HI,HJ,HK
• 2501 — Recovering synchronous error
• 2502 — Block Delete command error
• 2503 — End sequence name error
• 2504 — PREMIUM THREAD Command error
• 2505 — CAM machine no spec.
• 2506 — Tool center point control not possible
• 2507 — CHP command error
• 2508 — Machining mode command format
• 2509 — MULTI-MACHINING CYCLE Return point
• 2510 — Mistake in torque skip cycle command
• 2511 — Remote buffer operation
• 2512 — M-tool spindle overload
• 2513 — Coordinate calculation
• 2514 — MULTI CYCLE C-axis shift
• 2515 — Remote buffer operation time out
• 2516 — Remote buffer operation communication error
• 2517 — W-axis control mode
• 2518 — Synchronized tapping command
• 2519 — Tailstock control command
• 2520 — Mistake in TP command
• 2521 — Mistake in BT command
• 2522 — Mistake in BA command
• 2523 — Thermistor error
• 2524 — Mistake in AT command
• 2525 — Chuck coordinate change condition
• 2528 — Program selection unsuitable
• 2529 — Thermal deviation compensation
• 2530 — Machining process instruction no.
• 2531 — Mirror turning mode
• 2532 — System variable set condition error
• 2533 — Steady rest over interference pos.
• 2534 — LBB turret rotation impossible
• 2536 — Coordinate movement rotation copy
• 2537 — SLANT PROCESS MODE
• 2538 — Incorrect system variable
• 2539 — Mistake in B command
• 2541 — PROGRAM PRINT command
• 2542 — Feed axis retract function command
• 2543 — Turret index error position
• 2544 — TOOL-ID TOOL DATA
• 2545 — MULTI-MACHINING CYCLE LD
• 2546 — MULTI-MACHINING CYCLE LK
• 2547 — No decimal point
• 2548 — X-, Z-axis synchronized feed mode
• 2549 — Tool no. mismatch after ATC sequence restart
• 2550 — Home position no spec.
• 2551 — External home position command
• 2552 — Barrier area
• 2555 — Linear guide cover interference area command
• 2557 — Illegal steady rest command
• 2558 — Turning position selection
• 2559 — Attachment rotation not possible
• 2561 — Illegal system command variable
• 2562 — Tool posture fluctuation reduction
• 2563 — Mistake in TE command
• 2564 — Index disable position
• 2565 — Load monitor system variable
• 2566 — MULTI-MACHINING CYCLE No M-tool cycle command
• 2567 — No helical cutting specifications
• 2568 — Mistake in OF command
• 2569 — Thermal deviation comp. backup failure
• 2570 — W-axis position condition
• 2571 — W-axis position no spec.
• 2572 — Mistake in RC command
• 2573 — Taper cutting cycle
• 2575 — Mistake in TD,TDG,OS commands
• 2576 — Mistake in H command
• 2577 — No axis movement command
• 2578 — NO D COMMAND
• 2579 — NO L COMMAND
• 2580 — Mistake in XS command
• 2581 — CAM data deployment mode
• 2582 — CAM data file write protect
• 2583 — Compensation value overflow
• 2584 — CON speed XS-axis
• 2585 — XS-axis command turret mode
• 2586 — Synchronous mode execution impossible
• 2587 — No A command
• 2588 — Mistake in OF command
• 2589 — Definition conditions
• 2590 — Y-axis command
• 2591 — Mistake in point command
• 2592 — Transport barrier entry command
• 2593 — Mistake in CF command
• 2594 — Mistake in RJ command
• 2595 — Synchronized rotation speed over
• 2596 — Synchronized tap overload
• 2597 — G15 command
• 2598 — No Spec code. Tool information management spec
• 2599 — Command not possible while mounting LBB.
• 2600 — LAW-V machine no spec.
• 2601 — Unable to issue T/TE command simultaneously
• 2602 — SCHEDULE PROGRAM main program load
• 2603 — Spindle rotation fluctuation control no spec.
• 2604 — Tow-along steady rest no spec.
• 2605 — Tow-along tailstock no spec.
• 2606 — READ/WRITE file open
• 2607 — Mistake in AP command
• 2608 — Mistake in ON command
• 2609 — A-axis control no spec.
• 2610 — Zero offset select inpossible
• 2611 — Spindle fluctuation control no spec.
• 2612 — Mistake in TR command
• 2613 — Mistake in MTM command
• 2614 — Mistake in MTS command
• 2615 — Mistake in MGS command
• 2616 — B-axis mode
• 2617 — Zero setting condition
• 2618 — Workpiece detection sensor not ready
• 2619 — Mistake in SW command
• 2622 — Unset system variable read
• 2623 — B-axis no spec.
• 2624 — Tow-along steady rest type-B no spec
• 2625 — Tow-along steady rest movement condition
• 2626 — W-axis overlap
• 2628 — Mistake in TW command
• 2629 — Mistake in FW command
• 2630 — Mistake in SC command
• 2631 — DNC-DT Path name
• 2632 — DNC-DT Program select
• 2633 — DNC-DT Preload error
• 2634 — DNC-DT Delete error
• 2635 — Y-axis mode
• 2637 — No axis movement command
• 2638 — A/B saddle synchronized motion command
• 2639 — Unable to issue C-axis command during helical cutting
• 2640 — AC thread rotation count error
• 2641 — AC thread fluctuation control not possible
• 2642 — READ/WRITE No empty SAT
• 2643 — READ/WRITE File open
• 2644 — Unusable PRINT request
• 2645 — YS-axis position
• 2646 — SYSTEM VARIABLE C-axis separation
• 2648 — MG tool ready cycle no spec.
• 2649 — SYSTEM VARIABLE Y-axis mode
• 2650 — SYSTEM VARIABLE B-axis mode
• 2651 — C-axis multi rotation mode
• 2652 — Mistake in HA command
• 2653 — Mistake in MN command
• 2654 — Hob circular cutting command
• 2655 — Hob cutting command
• 2657 — SYSTEM VARIABLE C-axis connect
• 2658 — B-axis independent encoder error
• 2659 — NC tailstock position error
• 2662 — NC TAILSTOCK no spec.
• 2663 — Turning cut condition interlock
• 2667 — X-axis mirror image coordinates selected
• 2668 — X-axis mirror image coordinates impossible
• 2671 — C-axis sync control no spec.
• 2672 — C-axis sync command format
• 2674 — Default status macro cannot be executed
• 2675 — Tool posture command error
• 2676 — Tool posture command angle conversion error
• 2677 — Attachment change not possible
• 2678 — SPM contour control not possible
• 2679 — Mistake in Q command
• 2682 — Magnetic encoder speed detection error
• 2683 — MCS Rotary encoder 5 initialization failure
• 2684 — MCS Rotary encoder 5 error
• 2685 — MCS Rotary encoder 4 initialization failure
• 2686 — MCS Rotary encoder 4 error
• 2687 — MCS Rotary encoder 3 initialization failure
• 2688 — MCS Rotary encoder 3 error
• 2689 — MCS Rotary encoder 2 error
• 2690 — MCS Rotary encoder 1 initialization failure
• 2691 — MCS Rotary encoder 1 error
• 2692 — MCS Linear scale 4 initialization failure
• 2693 — MCS Linear scale 4 error
• 2694 — MCS Linear scale 3 initialization failure
• 2695 — MCS Linear scale 3 error
• 2696 — MCS Linear scale 2 initialization failure
• 2697 — MCS Linear scale 2 error
• 2698 — MCS Linear scale 1 initialization failure
• 2699 — MCS Linear scale 1 error
• 2700 — No workpiece confirmation error
• 2701 — Sequencer Error
• 2702 — Spindle command during C-axis connection
• 2703 — Chucking miss
• 2704 — Chucking miss air off order impossible
• 2705 — Tailstock quill over advance
• 2706 — Polygon cutting command condition
• 2707 — Invalid command during polygon cutting
• 2708 — Invalid rotation tool gear
• 2709 — Sub-spindle synchronization interlock
• 2710 — Sub-spindle synchronization cutting
• 2711 — Door open
• 2712 — ATC no spec.
• 2713 — Invalid ATC syntax
• 2714 — Invalid ATC TC no.
• 2716 — Invalid ATC TL no.
• 2717 — Invalid ATC MT no.
• 2718 — Invalid ATC MG no.
• 2719 — Invalid ATC command
• 2720 — M06/M228 interlock
• 2721 — Turret number mismatch
• 2722 — Robot/Loader request illegal
• 2723 — ATC next tool preparation interlock
• 2724 — Invalid ATC sub arm
• 2725 — Invalid RS tool L/M
• 2726 — Magazine encoder read
• 2727 — Magazine rotation interlock
• 2728 — Invalid magazine tool no.
• 2729 — No magazine return pot
• 2730 — Tool insertion interlock
• 2732 — Tailstock sleeve position data error
• 2733 — Coolant flow
• 2734 — Coolant level
• 2735 — Spindle low rotation command
• 2736 — SVP time constant switching no spec.
• 2737 — Invalid tailstock switch position
• 2738 — Synchronous hobbing interlock
• 2739 — Invalid synchronous hobbing mode
• 2740 — Incorrect magazine tool data
• 2741 — Touch setter unlock time over
• 2742 — Setup switch ON
• 2743 — Irregular coolant level
• 2744 — Tool breakage
• 2745 — Low high-pressure coolant pressure
• 2746 — Hydraulic oil unit error
• 2747 — Index disable position
• 2748 — CPU fan stop
• 2749 — Hydraulic oil level lower limit
• 2750 — Tool monitoring unit error detection
• 2751 — Coolant/Oil mist command
• 2752 — Air pressure
• 2753 — Unable to change tool
• 2754 — Invalid coolant command
• 2755 — Semi-dry unit error
• 2756 — Actual tool data setting
• 2757 — Oil mist unit error
• 2758 — Invalid position data
• 2759 — Coolant discharge error
• 2760 — Sub-spindle rotation tool interlock
• 2761 — W-axis overlap mode
• 2762 — Chucking miss
• 2763 — Coolant filter
• 2764 — Coolant error
• 2765 — Chip conveyer filter clogged
• 2766 — Invalid M-tool spindle command
• 2767 — M-spindle low rotation interlock
• 2768 — Program check mode interlock
• 2769 — Invalid spindle control command
• 2770 — SVP time constant switching command
• 2771 — APC clamp confirmation
• 2772 — APC system mode
• 2773 — APC M command
• 2774 — Thread cutting cycle interlock
• 2775 — Sensor head interlock
• 2776 — M command not completed
• 2777 — Cross rail positioning sensor error
• 2778 — Cross rail motor overload
• 2779 — Axis lube motor overload
• 2780 — Axis lube pressure ON confirmation
• 2781 — No AT command
• 2782 — Axis lube pressure OFF confirmation
• 2783 — Oil hole motor overload
• 2784 — Invalid MT command
• 2785 — Invalid AT command
• 2786 — No S command
• 2787 — No SB command
• 2788 — Invalid SB command
• 2789 — Coolant tank filter clogged
• 2790 — Shower coolant motor overload
• 2791 — M spindle head cooling unit
• 2792 — Invalid RH command
• 2793 — Incorrect attachment index position
• 2794 — Mist air lube unit
• 2795 — Warming up error
• 2796 — Sequence restart
• 2797 — Axis interlock release
• 2798 — Invalid BC command
• 2800 — Alarm detected from externally connected device
• 2801 — Turret rotation interlock
• 2802 — Invalid long boring bar command
• 2803 — ATC tool data setting
• 2804 — Attachment control
• 2805 — Limit confirmation impossible
• 2806 — Door interlock
• 2807 — Invalid M code
• 2848 — Chip conveyer overload
• 2849 — Sensor unit in interference range
• 2850 — External request interlock
• 2851 — Machine change M-code
• 2852 — Hand open/close interlock
• 2853 — Teaching operation interlock
• 2854 — Machine linked M-code
• 2855 — Coolant filter
• 2856 — Coolant motor overload
• 2857 — UNUSABLE M-code
• 2858 — Hand slide advance interlock
• 2887 — Coupling device interlock
• 2888 — Lube tank level
• 2890 — Workpiece clamp miss
• 2891 — Tailstock air miss
• 2892 — Unable to execute air shut-off command
• 2893 — Hydraulic oil controller faulty
• 2894 — Spindle lubricant controller error
• 2895 — Coolant controller error
• 2896 — No touch setter
• 2897 — Unloader no spec.
• 2898 — Unloader interference position
• 2899 — Gauge error
• 2900 — DIRECTION V variable
• 2901 — DIRECTION Check address
• 2902 — DIRECTION Data operation
• 2903 — DIRECTION Character use
• 2904 — DIRECTION Numerical data
• 2905 — DIRECTION Parameter/point
• 2906 — DIRECTION Register
• 2907 — DIRECTION F
• 2908 — DIRECTION E
• 2909 — DIRECTION Sequence no.
• 2910 — UNUSABLE G-code
• 2911 — UNUSABLE M-code
• 2912 — UNUSABLE Address character
• 2913 — UNUSABLE Mnemonic
• 2914 — UNUSABLE Left side direction
• 2915 — EXPRESSION Calculation
• 2916 — EXPRESSION Syntax
• 2917 — EXPRESSION Right side
• 2918 — EXPRESSION Left side
• 2919 — EXPRESSION Buffer over
• 2920 — VARIABLE Buffer over
• 2921 — PROGRAM DIRECT Program name
• 2922 — PROGRAM DIRECT V variable
• 2923 — PROGRAM DIRECT Character use
• 2924 — PROGRAM DIRECT G-code
• 2925 — BRANCH Sequence name
• 2926 — BRANCH Condition
• 2927 — Parameter setting illegal
• 2928 — Parameter playback impossible
• 2929 — Register setting impossible
• 2930 — Program plus var. limit over
• 2931 — Program minus var. limit over
• 2932 — Program request illegal
• 2933 — Program request impossible
• 2934 — Program external request impossible
• 2935 — No program selection
• 2936 — No program
• 2937 — Program end code
• 2938 — Program analysis complete
• 2939 — SUB PROGRAM stack
• 2940 — SUB PROGRAM Program name
• 2941 — SUB PROGRAM Buffer over
• 2942 — Command impossible while running
• 2943 — Data file read
• 2944 — Comment end code not found
• 2945 — Equal does not exist
• 2946 — No spec.
• 2948 — DIRECTION Y
• 2949 — DIRECTION Z
• 2950 — DIRECTION D
• 2951 — DIRECTION L
• 2952 — DIRECTION SU
• 2953 — DIRECTION Torque limit
• 2954 — PROGRAM DIRECT M-code
• 2955 — PROGRAM DIRECT Equal
• 2956 — Machine change M-code
• 2957 — G22 feed
• 2958 — Main sequence
• 2959 — Barrier limit
• 2960 — User reserve code
• 2961 — Calculation function no spec.
• 2962 — Subscript function no spec.
• 2964 — NC program selection
• 2965 — EXPRESSION subscript
• 2966 — M code time over
• 2967 — Cycle time over
• 2968 — Program selection
• 2969 — G23 FEED
• 2970 — DIRECTION X
• 2971 — DIRECTION I
• 2972 — DIRECTION J
• 2973 — DIRECTION K
• 2974 — PROGRAM DIRECT hexadecimal data
• 2975 — PROGRAM DIRECT character string
• 2976 — Stopper position data illegal
• 2977 — Program selection unsuitable
• 2978 — DIRECTION V
• 2979 — DIRECTION C
• 2980 — No decimal point
• 2981 — DIRECTION Q
• 2982 — Time over

Machine-side conditions and peripheral equipment — coolant, lubrication, ATC, robot/loader and auxiliary unit faults.

• 3055 — Device temperature too high
• 3056 — Non-functioning device detected
• 3057 — Unable to start during virus scan
• 3120 — Overload detected.
• 3122 — Maintenance (by user) necessary
• 3132 — VDU communication error
• 3133 — VDU detected error
• 3134 — VDU initialization failure
• 3135 — MCS DD encoder link error
• 3136 — MCS DD Encoder error
• 3137 — MCS DD Encoder (slave sensor) error
• 3138 — MCS DD encoder initialization failure
• 3139 — MCS DD encoder (slave sensor) initialization failure
• 3144 — MCS Power supply unit overload
• 3150 — MCS Undefined alarm number
• 3151 — MCS Inverter unit fault
• 3152 — Mistake in data from MCS to NC
• 3153 — MCS CON APA deviation
• 3154 — MCS Power supply unit error
• 3155 — MCS Converter link error
• 3156 — MCS DC-bus voltage alarm
• 3157 — MCS Motor overcurrent
• 3158 — MCS Power unit overheat
• 3159 — MCS Power unit overload
• 3160 — MCS Supply voltage flutter
• 3161 — MCS Inverter capacity differs from spec.
• 3162 — MCS Winding change failure
• 3163 — MCS Encoder link error
• 3164 — MCS Encoder detected error.
• 3165 — MCS Encoder initialization failure
• 3166 — MCS Encoder with shaft detected error
• 3167 — MCS Encoder with shaft initialization failure
• 3168 — MCS ABSO SCALE error
• 3169 — MCS ABSO SCALE initialization failure
• 3170 — MCS Magnetic encoder alarm
• 3171 — MCS Resolver alarm
• 3172 — MCS Pulse generator count over
• 3173 — MCS Motor overheat
• 3174 — MCS Servo link error
• 3175 — MCS Servo link disconnection
• 3176 — Mistake in data from NC to MCS
• 3177 — MCS Servo data error
• 3178 — MCS Illegal command
• 3179 — MCS CON speed over
• 3180 — MCS Speed command over
• 3181 — MCS DIFF over
• 3182 — MCS APA speed over
• 3183 — MCS Full-closed APA error
• 3184 — MCS Over speed
• 3185 — MCS Speed deviation over
• 3186 — MCS Collision detected
• 3187 — MCS Urgent-stop time over
• 3188 — MCS Belt is broken
• 3189 — MCS Axis change control error
• 3190 — MCS Independent encoder initialization failure
• 3191 — MCS Calculated current position lies outside range
• 3192 — MCS Motor overload
• 3194 — MCS ABSO SCALE sub-slider detected error
• 3195 — MCS Tandem control communication error
• 3196 — MCS Full abso scale link error
• 3197 — MCS Full abso scale error
• 3198 — MCS Full abso scale initialization failure
• 3199 — MCS Axis stop signal error
• 3202 — User reserve code
• 3203 — Warm up run
• 3204 — Running time over
• 3205 — Work counter over
• 3206 — Cycle time over
• 3207 — DNC Start conditions
• 3208 — DNC Initialization sequence impossible
• 3209 — DNC Illegal text from host
• 3210 — DNC Incorrect machine No.
• 3211 — DNC Text format error
• 3212 — DNC Text receipt error
• 3213 — DNC Text transmission error
• 3214 — FMS Coupling mode change
• 3215 — FMS HOST CPU alarm
• 3216 — FMS Operation mode select
• 3217 — DNC-B buffer operation
• 3218 — DNC-B buffer operation change
• 3226 — Common unit illegal
• 3231 — Program select
• 3232 — Load monitor overload
• 3238 — ROBOT alarm/reset
• 3240 — LOADER alarm/reset
• 3241 — Post-process gauging Unable to transmit
• 3242 — Post-process gauging Unable to receive
• 3243 — Post-process gauging Time out
• 3244 — Post-process gauging Data format error
• 3245 — Gauging data out
• 3246 — CEJ MATIC Data NG
• 3247 — CEJ MATIC Data read
• 3248 — Size catcher Data NG
• 3249 — Size catcher Gauging error
• 3250 — Size catcher Unable to transmit
• 3251 — Size catcher Unable to receive
• 3252 — Size catcher Time out
• 3253 — Size catcher Data format error
• 3254 — Schedule program start
• 3255 — Main program start
• 3261 — Tool life management No spare tool.
• 3264 — RS-232C communication illegal
• 3266 — Workpiece counter full count
• 3271 — Gauging sensor battery change
• 3279 — DNC Machining start conditions
• 3280 — DNC Data receipt start conditions
• 3289 — Load monitor low load
• 3295 — Quality check alarm
• 3300 — Tool data output
• 3314 — External tool offset input
• 3316 — Position encoder adjustment required.
• 3319 — DNC Ethernet receipt command not allowed.
• 3320 — DNC Ethernet receipt error
• 3321 — DNC Ethernet transmission error
• 3331 — NC tailstock position error
• 3332 — Reboot machine.
• 3682 — Magnetic encoder speed detection error
• 3683 — MCS Rotary encoder 5 initialization failure
• 3684 — MCS Rotary encoder 5 error
• 3685 — MCS Rotary encoder 4 initialization failure
• 3686 — MCS Rotary encoder 4 error
• 3687 — MCS Rotary encoder 3 initialization failure
• 3688 — MCS Rotary encoder 3 error
• 3689 — MCS Rotary encoder 2 error
• 3690 — MCS Rotary encoder 1 initialization failure
• 3691 — MCS Rotary encoder 1 error
• 3692 — MCS Linear scale 4 initialization failure
• 3693 — MCS Linear scale 4 error
• 3694 — MCS Linear scale 3 initialization failure
• 3695 — MCS Linear scale 3 error
• 3696 — MCS Linear scale 2 initialization failure
• 3697 — MCS Linear scale 2 error
• 3698 — MCS Linear scale 1 initialization failure
• 3699 — MCS Linear scale 1 error
• 3700 — Power save ON
• 3701 — CPU temperature
• 3702 — Warm up run
• 3703 — Oil filter
• 3704 — Lube tank flow
• 3705 — Lube tank level
• 3706 — Spindle lube pressure
• 3707 — Spindle cooler error
• 3708 — Oil cooler error
• 3709 — Coolant level
• 3710 — Air blow pressure
• 3711 — Air pressure
• 3712 — Program selection interlock
• 3713 — Chip conveyer overload
• 3714 — ZA-axis overload
• 3715 — ZB-axis overload
• 3716 — XA-axis overload
• 3717 — XB-axis overload
• 3718 — Coupling device error
• 3719 — ROBOT control
• 3720 — ROBOT alarm/reset
• 3721 — ROBOT/LOADER control
• 3722 — LOADER alarm/reset
• 3723 — Schedule program start
• 3724 — Main program start
• 3725 — CEJ MATIC data NG
• 3726 — CEJ MATIC data read
• 3727 — Auto power off impossible
• 3728 — Oil cooler level
• 3729 — Coolant error
• 3730 — Coolant flow
• 3731 — Coolant abnormal
• 3732 — Robot/loader axis safety speed over
• 3733 — Robot/loader safety speed monitor error
• 3734 — ATC step time over
• 3735 — Next tool preparation impossible
• 3736 — Coolant filter
• 3737 — Mist collector
• 3738 — Mode switch operation prohibited
• 3739 — Control box air conditioner error
• 3740 — Air filter clogged
• 3741 — Index chuck oil level
• 3742 — ATC-axis circuit breaker
• 3743 — ATC-axis motor overload
• 3744 — Chucking miss air
• 3745 — Mist lubrication unit
• 3746 — External start switch
• 3747 — NC start button
• 3748 — Door sensor
• 3749 — Automatic lubrication system error
• 3750 — Tailstock absolute encoder error
• 3751 — Invalid external tool offset input
• 3752 — Coolant supply
• 3753 — Drain tank
• 3754 — Mist collector
• 3755 — Workpiece conveyor error
• 3756 — Unmachined workpiece detection
• 3757 — Bar feeder error
• 3758 — Oil mist error
• 3759 — Tool monitoring unit error detection
• 3760 — Fan cooling unit pressure
• 3761 — TOOL change not possible
• 3762 — ACC step time over
• 3763 — Switch disabled
• 3764 — Oil controller unit
• 3765 — Spindle vibration sensor
• 3766 — Coupling device interlock
• 3767 — Tailstock holding miss check air
• 3768 — Irregular coolant level
• 3769 — Side cover open
• 3770 — Safety door open
• 3771 — Lube tank motor run time over
• 3772 — Coolant flow
• 3773 — Earthquake detected
• 3774 — EC circuit breaker
• 3775 — Lubrication unit error
• 3777 — Air blow flow
• 3778 — M axis cooling fan overload
• 3779 — APC system conditions
• 3780 — Touch setter unit error
• 3781 — EC overload
• 3782 — Sensor contact signal error
• 3783 — ATC interlock
• 3784 — Fire extinguish unit power OFF
• 3785 — Spindle lubrication unit
• 3786 — Chip flush-out motor overload
• 3787 — M-axis unit command mismatch
• 3788 — AAC system condition
• 3789 — Air dryer unit error
• 3790 — Ext. program select parity check
• 3791 — Mist air lubrication unit
• 3792 — Chucking miss
• 3793 — Coolant level low
• 3794 — Power source unit overload
• 3795 — Hydraulic oil unit
• 3796 — RSS unit battery error
• 3797 — RSS unit communication error
• 3798 — Unloader interlock
• 3800 — Transfer data error
• 3843 — Safety fence open
• 3844 — Invalid loader grease lubrication input
• 3845 — Coolant level lower limit
• 3846 — M/C panel at interfering position
• 3847 — Invalid limit/proximity switch
• 3848 — Anti-gouge unit faulty
• 3849 — Tool counter full count
• 3850 — External alarm
• 3851 — Tool counter faulty
• 3852 — Tail stock chuck position
• 3853 — Invalid loader limit/proximity switch
• 3854 — Chip conveyor stop
• 3855 — Oil air unit oil level low
• 3856 — Coolant motor overload
• 3857 — Oil skimmer overload
• 3858 — Chuck grip confirmation unit faulty
• 3859 — Fire extinguisher error
• 3860 — Fire extinguisher power OFF or error
• 3861 — Chip conveyer filter clogged
• 3862 — Filtration unit error
• 3874 — Sub chip conveyor error
• 3875 — Absolute encoder controller error
• 3876 — Workpiece loading unit stop signal ON
• 3877 — Workpiece counter full count
• 3878 — Concentrated chip conveyor
• 3879 — Gauging NG
• 3880 — Spindle air purge pressure
• 3881 — Turnover cycle time over
• 3882 — Start impossible
• 3883 — Chip crusher error
• 3884 — Workpiece puller operation incomplete
• 3885 — No workpiece
• 3886 — Workpiece present
• 3887 — Temperature control unit error
• 3888 — Chip conveyor faulty
• 3889 — External start signal ON
• 3890 — Low level in oil tank
• 3891 — Multi-counter tool life
• 3892 — Hydraulic oil level lower limit
• 3893 — Hydraulic unit oil controller
• 3894 — Spindle lubrication controller error
• 3895 — Coolant controller error
• 3896 — Tool change count-up
• 3897 — Workpiece stocker full
• 3898 — Cooler error
• 3900 — User reserve code
• 3901 — External

Operator messages and interlocks — often informational (open a door, wait for a cycle) rather than a hardware failure.

• 4035 — Replace memory board battery
• 4036 — Key-code data receipt error
• 4037 — CCP-CPU error
• 4052 — PLC backup data file write
• 4054 — ACP key-code data receipt error
• 4055 — Safety speed clamping
• 4056 — Adjusting Type-J encoder
• 4057 — Battery life
• 4058 — Previous backup error
• 4059 — Backup file error
• 4060 — AlarmService internal error
• 4061 — UPS Service error
• 4062 — Remote Diagnosis error
• 4063 — DNC2 communication error
• 4064 — Awaiting establishment of DeviceNet
• 4065 — FL-net transmission error
• 4066 — FL-net transmission failure
• 4067 — Maintenance necessary
• 4068 — Non-responsive software detected
• 4069 — Turret index sequence has not ended.
• 4070 — Solid model position error
• 4071 — CAS environment file cannot be changed
• 4072 — Turret position error
• 4076 — CAS software calculation error
• 4077 — Turning interlock of CAS
• 4078 — Error occurred during CAS
• 4080 — Collision Avoidance Function OFF
• 4081 — In-position/droop check waiting status
• 4083 — Windows updated. Reboot
• 4084 — Virus has been detected.
• 4085 — Fan motor error at panel computer unit
• 4086 — UPS not functioning
• 4087 — Non-functioning device detected
• 4088 — Virus Detect Function active
• 4090 — Machine relocation detected
• 4091 — Var. lost motion cannot be applied.
• 4092 — MCS Parameter learning
• 4100 — Collision avoidance position
• 4101 — CAS software environment being changed
• 4102 — Awaiting CAS software process
• 4103 — Drawing speed over
• 4104 — CAS processing time over
• 4105 — Collision block detected
• 4106 — Collision Avoidance system OFF
• 4107 — Awaiting CAS check result
• 4108 — Inaccurate material shape
• 4109 — CAS operating in rapid mode
• 4110 — Turret collision check not performed
• 4120 — Overload detected
• 4121 — General overload detection disabled
• 4122 — Maintenance (by user) necessary
• 4130 — MCS Inertia identification
• 4131 — VDU initialization failure
• 4132 — VDU communication error
• 4133 — VDU error
• 4134 — MCS Alarm-D occurred
• 4135 — MCS DD encoder link error
• 4136 — MCS DD encoder error
• 4137 — MCS DD encoder (slave sensor) detected error
• 4138 — MCS DD encoder initialization failure
• 4139 — MCS DD encoder (slave sensor) initialization failure
• 4141 — MCS Push reset button to stop spindle
• 4144 — MCS power supply unit overload
• 4145 — MCS Drive unit external cooling fan stop
• 4147 — MCS Drive unit internal cooling fan stop
• 4148 — MCS Power supply unit external cooling fan stop
• 4149 — MCS Power supply unit internal cooling fan stop
• 4150 — MCS Undefined alarm number
• 4151 — MCS Inverter unit fault
• 4152 — Mistake in data from MCS to NC
• 4153 — MCS CON APA deviation
• 4154 — MCS Power supply unit error
• 4155 — MCS Converter link error
• 4156 — MCS DC-bus voltage alarm
• 4157 — MCS Motor overcurrent
• 4158 — MCS Power unit overheat
• 4159 — MCS Power unit overload
• 4160 — MCS Supply voltage flutter
• 4161 — MCS Inverter capacity differs from spec.
• 4162 — MCS Winding change failure
• 4163 — MCS Encoder link error
• 4164 — MCS Encoder detected error
• 4165 — MCS Encoder initialization failure
• 4166 — MCS Encoder with shaft detected error
• 4167 — MCS Encoder with shaft initialization failure
• 4168 — MCS ABSO SCALE error
• 4169 — MCS ABSO SCALE initialization failure
• 4170 — MCS Magnetic encoder alarm
• 4171 — MCS Resolver alarm
• 4172 — MCS Pulse generator count over
• 4173 — MCS Motor overheat
• 4174 — MCS Servo link error
• 4175 — MCS Servo link disconnection
• 4176 — Mistake in data from NC to MCS
• 4177 — MCS Servo data error
• 4178 — MCS Illegal command
• 4179 — MCS CON speed over
• 4180 — MCS Speed command over
• 4181 — MCS DIFF over
• 4182 — MCS APA speed over
• 4183 — MCS Full-closed APA error
• 4184 — MCS Over speed
• 4185 — MCS Speed deviation over
• 4186 — MCS Collision detected
• 4187 — MCS Urgent-stop time over
• 4188 — MCS Belt is broken
• 4190 — MCS Independent encoder initialization failure
• 4191 — MCS Calculated current position lies outside range
• 4192 — MCS Motor overload
• 4194 — MCS ABSO SCALE sub-slider detected error
• 4195 — MCS Tandem control communication error
• 4196 — MCS Full abso scale link error
• 4197 — MCS Full abso scale error
• 4198 — MCS Full abso scale initialization failure
• 4199 — MCS Axis stop signal error
• 4200 — Reboot enabled parameter set
• 4201 — MACHINING MANAGEMENT data backup stop
• 4202 — DNC-B Communication system abort
• 4203 — DNC-B Communication error
• 4204 — DNC-B Message format error
• 4205 — H1 turret interference barrier parameter not set
• 4206 — SPM Parameter unsuitable
• 4207 — Unable to execute Hi-CUT Pro control
• 4208 — G265/G264 commands: Unusable address character
• 4209 — Hi-CUT Pro parameter out of range (replacing)
• 4210 — SPM contour control not possible
• 4211 — SPM parameter out of range (replacing)
• 4214 — RS232C communication not ready
• 4215 — Communication buffer over
• 4216 — Communication procedure No response
• 4217 — Communication procedure NAK/WACK
• 4218 — Communication procedure Illegal text
• 4219 — Communication procedure ENQ
• 4220 — Communication procedure EOT
• 4221 — Communication procedure TTD
• 4223 — Motor not ready to start
• 4224 — Canceling stroke end limit
• 4225 — Pitch compensation data calculation
• 4226 — MSB load error
• 4227 — External start not possible
• 4228 — Synchronized rotation speed over
• 4230 — Torque limit recovery
• 4232 — Backup data read/write
• 4237 — Magazine operation panel communication error
• 4238 — Please open magazine door
• 4240 — Tool life management No spare tool
• 4242 — Parameter set value incorrect
• 4245 — Waiting program selection during program operation.
• 4247 — Main spindle max. speed designation
• 4248 — DNC NC receipt start conditions
• 4249 — Tool life warning
• 4251 — Axis feed rate restriction
• 4252 — Detector operation check mode
• 4258 — Y-axis cancel mode
• 4261 — Workpiece counter over
• 4267 — PLC link error
• 4268 — PLC communication error
• 4269 — ROBOT control
• 4274 — User reserve code
• 4281 — Workpiece counter over
• 4284 — Thermistor error
• 4285 — Thermal deviation compensation
• 4288 — PSC Learn converge protect error
• 4289 — Spindle able to enter transportation barrier
• 4290 — TCP/IP communication error
• 4291 — Position encoder auto adjustment
• 4292 — Please check the program
• 4294 — Extended Y-axis plus variable limit
• 4295 — TDC parameter not set
• 4297 — Main Magazine tool Quantity over
• 4298 — DNC Ethernet communication error
• 4300 — B-axis independent encoder connecting
• 4301 — Tail-stock position error
• 4302 — Please supply oil of chuck
• 4303 — Movement to sizing position stopped
• 4304 — No axis movement after offset change
• 4305 — Y-axis not at turning position
• 4306 — Turret movement decelerating
• 4307 — Alarm-A at other system
• 4308 — X-axis over limit
• 4309 — Clutch A slip monitor OFF
• 4311 — Interrupt program
• 4314 — Learning required for cam data
• 4315 — Permissible value exceeded
• 4316 — Manual feed invalid
• 4345 — Unable to execute feed axis retract function
• 4346 — ZA-W interference parameter not set
• 4347 — TDC invalid
• 4348 — X-C-axis coordinate value error
• 4349 — Mode switching impossible
• 4682 — Magnetic encoder speed detection error
• 4683 — MCS Rotary encoder 5 initialization failure
• 4684 — MCS Rotary encoder 5 error
• 4685 — MCS Rotary encoder 4 initialization failure
• 4686 — MCS Rotary encoder 4 error
• 4687 — MCS Rotary encoder 3 initialization failure
• 4688 — MCS Rotary encoder 3 error
• 4689 — MCS Rotary encoder 2 error
• 4690 — MCS Rotary encoder 1 initialization failure
• 4691 — MCS Rotary encoder 1 error
• 4692 — MCS Linear scale 4 initialization failure
• 4693 — MCS Linear scale 4 error
• 4694 — MCS Linear scale 3 initialization failure
• 4695 — MCS Linear scale 3 error
• 4696 — MCS Linear scale 2 initialization failure
• 4697 — MCS Linear scale 2 error
• 4698 — MCS Linear scale 1 initialization failure
• 4699 — MCS Linear scale 1 error
• 4700 — External cycle start interlock
• 4701 — Chip conveyer overload
• 4702 — Cycle start interlock
• 4703 — Canceling stroke end limit
• 4704 — Please open door
• 4705 — Door interlock all axis stop
• 4706 — Canceling door interlock
• 4707 — Enabling Switch faulty
• 4708 — ATC system mode
• 4709 — Power sequence error
• 4710 — Parameter non set
• 4711 — Spindle motor not ready to start
• 4712 — Reboot enabled parameter set
• 4713 — Executing power OFF sequence
• 4714 — Workpiece counter full count
• 4715 — Preparing for warming up
• 4716 — Motor not ready to start
• 4717 — Dual cycle start button interlock
• 4718 — Invalid parameter setting
• 4719 — Please open side cover
• 4720 — Dual cycle start button interlock
• 4721 — Feed rate limitation
• 4722 — System check mode
• 4723 — Machine enabling button pressed
• 4724 — Please open safety fence
• 4725 — Please close front door
• 4726 — Opposite side front door open
• 4727 — Safety fence open
• 4728 — Please close other side front door
• 4729 — Please open magazin door
• 4730 — Magazine door open
• 4731 — Multiple safety guards open
• 4732 — Gauging sensor power ON
• 4733 — Measurement system error
• 4734 — Please close safety guards
• 4735 — Full of chips
• 4736 — Sensor head
• 4737 — Other door open
• 4738 — Magazine OP panel COMM error
• 4739 — Turret not ready to start
• 4740 — 2nd Spindle control interlock
• 4741 — Magazine operation panel manual interrupt
• 4742 — Turret encoder offset disabled area
• 4743 — Turret index disabled area
• 4744 — Turnover cycle
• 4745 — REDUCE switch operation error
• 4746 — Tool change mode sw operation error
• 4747 — Gauging sensor battery change
• 4748 — Additional coolant level low
• 4749 — Please close door
• 4750 — Safety interlock
• 4751 — Tailstock quill interlock
• 4752 — Tailstock absolute coder error
• 4753 — Workpiece hand control
• 4754 — Bar stock empty
• 4755 — Roof window open interlock
• 4756 — Canceling robot/loader and machine interlock
• 4757 — Sp. oil air lub. air extraction mode
• 4758 — Index chuck adjust mode
• 4760 — Moving to home position
• 4761 — Override condition
• 4762 — Side cover open
• 4763 — Home position return interlock
• 4764 — Spindle orientation interlock
• 4765 — Setup not complete
• 4766 — Setup complete interlock
• 4767 — ACC safety door locking switch NG
• 4768 — Please open ACC safety door
• 4769 — ACC system mode
• 4770 — Mode switch NG
• 4771 — Magnet chuck unclamp cycle
• 4772 — Tool select switch mismatch
• 4773 — ATC shutter barrier area
• 4774 — Invalid zero offset no.
• 4775 — Please open spindle cover
• 4776 — Canceling interference detection
• 4777 — Mist collector power OFF
• 4778 — Side cover open
• 4779 — ATC shutter interlock cancel mode
• 4780 — Maintenance door open
• 4781 — Ladder gate open.
• 4782 — Workpiece stocker error
• 4783 — Workpiece stocker overload
• 4784 — Mist collector error
• 4785 — Self check counter full count
• 4786 — Coolant controller error
• 4787 — Manual tool change enabled
• 4788 — Chip conveyer stop
• 4789 — Sensor overstroke
• 4790 — Chucking miss air route clogged
• 4791 — Linear guide cover interference
• 4792 — Workpiece washer overload
• 4793 — Coolant filter
• 4794 — Sequencer alarm
• 4795 — Please open ceiling door
• 4796 — APC safety interlock
• 4797 — Please open APC door
• 4798 — APC door lock incomplete
• 4800 — Tow-along steady rest connection
• 4801 — Oil mist error
• 4802 — Turret rotation interlock
• 4803 — Cross rail positioning auto set mode
• 4804 — Workpiece washing gun error
• 4805 — Coolant unit error
• 4806 — Lube oil drain tank overflow
• 4807 — Axis lube level low
• 4808 — Coolant level low
• 4809 — ATC step time over
• 4810 — System check
• 4811 — Coolant tank upper level
• 4812 — Chip crusher error
• 4813 — Waiting for workpiece check
• 4814 — Chuck open/close interlock
• 4815 — Attachment turret rotating
• 4816 — Long boring bar interlock
• 4817 — Safety door open interlock
• 4818 — Attachment manual change mode
• 4819 — ATC door not at end of stroke
• 4820 — M-Spindle rotation limit
• 4821 — Steady rest interlock
• 4822 — Feed axis condition
• 4823 — Turret indexing at reduced speed
• 4824 — Setup mode
• 4825 — Axis position encoder control error
• 4826 — General overload detection disabled
• 4827 — Canceling chuck grasp interlockl
• 4828 — Please switch door interlock ON
• 4829 — NC tailstock thrust change interlock
• 4830 — Tool indexing not complete
• 4831 — Door interlock
• 4844 — Coupling device interlock
• 4845 — Coolant level warning
• 4846 — Unloader setting position parameter
• 4847 — Interference area intrusion
• 4848 — No lower table present signal
• 4849 — Coolant level
• 4850 — Safety fence interlock
• 4851 — Door interlock
• 4852 — Canceling stroke end limit
• 4853 — Robot/loader power sequence error
• 4854 — Loader interference
• 4855 — Front door open interlock
• 4856 — Please open safety fence
• 4857 — Please close safety fence
• 4858 — Feed rate limit
• 4859 — Teaching panel enabling switch error
• 4860 — Multiple safety guards open
• 4861 — Equip. safety fence parameter mismatch
• 4862 — Dual cycle start button interlock
• 4863 — Tool change count-up
• 4864 — Other door open
• 4865 — Performing turnover cycle
• 4866 — No workpiece
• 4867 — M-spindle angle uncertain
• 4868 — Cycle start interlock
• 4869 — Chuck was changed
• 4870 — Invalid servo data selection
• 4871 — Inside barrier
• 4872 — Tailstock fretting
• 4873 — Door open/close limit switch NG
• 4874 — XB cover interference
• 4875 — Please push the NC start button
• 4876 — Please discharge coolant
• 4877 — Invalid positioning point
• 4878 — Pulse handle mode
• 4879 — Curvic cover not attached
• 4880 — Measurement unit error
• 4881 — NG chute workpiece present
• 4882 — Quality check counter notice count
• 4883 — Tow-along tailstock unclamp
• 4884 — Tool counter full count
• 4885 — Quality check counter full count
• 4886 — Tool counter warning
• 4887 — Tailstock/Chuck Pedal Enable
• 4888 — Mode switch operation error
• 4889 — PLC link error
• 4890 — Dust collector in local mode
• 4891 — Chip conveyor in local mode
• 4892 — Chip conveyor error
• 4893 — OP panel not at retract position
• 4894 — Multi-counter tool life warning
• 4895 — Hydraulic fluid level low
• 4896 — Lubricant level
• 4897 — Gauging data ready time out
• 4898 — Power save ON
• 4899 — Lower turret origin return interlock
• 4900 — Motor not ready to start
• 4903 — Reboot enabled parameter set
• 4904 — Barrier intrusion
• 4905 — Safety speed clamping
• 4907 — Alarm-A at other system